diff --git a/libraries/base/dp/dp.peripheral.yaml b/libraries/base/dp/dp.peripheral.yaml
index ecc421c8c3541c69a6ffeb63783c520b7c246ad2..30d8efd01b1b5006110e7d8e43e546b8dedfa624 100644
--- a/libraries/base/dp/dp.peripheral.yaml
+++ b/libraries/base/dp/dp.peripheral.yaml
@@ -50,9 +50,247 @@ peripherals:
# MM port for mms_dp_fifo_from_mm.vhd / dp_fifo_from_mm.vhd
- slave_name: REG_MMDP_DATA # Use REG_, instead of preferred FIFO_, to match slave_port_name in pi_mmdp.py
slave_type: FIFO
- slave_description: "MMDP = write word to the MM to DP write FIFO"
+ slave_description: "MMDP = write word to the MM to DP write FIFO."
fields:
- - field_name: data
field_description: "Write data to the FIFO."
access_mode: WO
address_offset: 0x0
+
+ - peripheral_name: dp_shiftram # pi_dp_shiftram.py
+ peripheral_description: "Sample delay buffer with programmable delay for streaming data."
+ parameters:
+ # Parameters of dp_shiftram.vhd
+ - { name: g_nof_streams, value: 1 }
+ - { name: g_nof_words, value: 1024 }
+ - { name: g_data_w, value: 16 }
+ slave_ports:
+ # MM port for dp_shiftram.vhd
+ - slave_name: REG_DP_SHIFTRAM
+ slave_type: REG
+ slave_description: ""
+ number_of_slaves: g_nof_streams
+ fields:
+ - - field_name: shift
+ field_description: "Fill level of the sample delay buffer in number of data samples."
+ width: ceil_log2(g_nof_words)
+ access_mode: RW
+ address_offset: 0x0
+
+ - peripheral_name: dp_bsn_source # pi_dp_bsn_source.py
+ peripheral_description: "Block Sequence Number (BSN) source for timestamping blocks of data samples."
+ parameters:
+ # Parameters of dp_bsn_source_reg.vhd
+ - { name: g_nof_block_per_sync, value: 20 }
+ slave_ports:
+ # MM port for dp_bsn_source_reg.vhd
+ - slave_name: REG_DP_BSN_SOURCE
+ slave_type: REG
+ slave_description: ""
+ fields:
+ - - field_name: dp_on
+ field_description: |
+ "When 1 then enable BSN source, else when 0 disable BSN source. If dp_on_pps is 0,
+ then dp_on = 1 enables the BSN source immediately. To enable the BSN source at
+ the next PPS, then first set dp_on_pps = 1. Clearing dp_on stops the BSN source."
+ width: 1
+ access_mode: RW
+ address_offset: 0x0
+ - - field_name: dp_on_pps
+ field_description: "When 1 and dp_on = 1 then enable BSN source at next PPS."
+ width: 1
+ bit_offset: 1
+ access_mode: RW
+ address_offset: 0x0
+ - - field_name: nof_block_per_sync
+ field_description: "Number of blocks per sync interval."
+ access_mode: RW
+ address_offset: 0x4
+ - - field_name: bsn_lo
+ field_description: "Initial BSN[31:0]"
+ access_mode: RW
+ address_offset: 0x8
+ - - field_name: bsn_hi
+ field_description: "Initial BSN[63:32]"
+ access_mode: RW
+ address_offset: 0xC
+
+ - peripheral_name: dp_bsn_source_v2 # pi_dp_bsn_source_v2.py
+ peripheral_description: "Block Sequence Number (BSN) source with block time offset, for timestamping blocks of data samples."
+ parameters:
+ # Parameters of dp_bsn_source_reg_v2.vhd
+ - { name: g_nof_clk_per_sync, value: 200000000 }
+ - { name: g_block_size, value: 256 }
+ - { name: g_bsn_time_offset_w, value: 8 } # note: g_bsn_time_offset_w = ceil_log2(g_block_size)
+ slave_ports:
+ # MM port for dp_bsn_source_reg_v2.vhd
+ - slave_name: REG_DP_BSN_SOURCE_V2
+ slave_type: REG
+ slave_description: ""
+ fields:
+ - - field_name: dp_on
+ field_description: |
+ "When 1 then enable BSN source, else when 0 disable BSN source. If dp_on_pps is 0,
+ then dp_on = 1 enables the BSN source immediately. To enable the BSN source at
+ the next PPS, then first set dp_on_pps = 1. Clearing dp_on stops the BSN source."
+ width: 1
+ access_mode: RW
+ address_offset: 0x0
+ - - field_name: dp_on_pps
+ field_description: "When 1 and dp_on = 1, then enable BSN source at next PPS."
+ width: 1
+ bit_offset: 1
+ access_mode: RW
+ address_offset: 0x0
+ - - field_name: nof_block_per_sync
+ field_description: "Number of clock cycles per sync interval."
+ access_mode: RW
+ address_offset: 0x4
+ - - field_name: bsn_init_lo
+ field_description: "Initial BSN[31:0]"
+ access_mode: RW
+ address_offset: 0x8
+ - - field_name: bsn_init_hi
+ field_description: "Initial BSN[63:32]"
+ access_mode: RW
+ address_offset: 0xC
+ - - field_name: bsn_time_offset
+ field_description: "The BSN block time offset in number of clock cycles, with respect to the PPS."
+ width: g_bsn_time_offset_w
+ access_mode: RW
+ address_offset: 0x10
+
+ - peripheral_name: dp_bsn_scheduler # pi_dp_bsn_scheduler.py
+ peripheral_description: "Schedule a trigger at a certain Block Sequence Number (BSN) instant."
+ slave_ports:
+ # MM port for dp_bsn_scheduler_reg.vhd
+ - slave_name: REG_DP_BSN_SCHEDULER
+ slave_type: REG
+ slave_description: ""
+ fields:
+ - - field_name: scheduled_bsn_lo
+ field_description: "Write scheduled BSN lo, read current BSN lo. First access lo, then hi."
+ access_mode: RW
+ address_offset: 0x0
+ - - field_name: scheduled_bsn_hi
+ field_description: "Write scheduled BSN hi, read current BSN hi. First access lo, then hi."
+ access_mode: RW
+ address_offset: 0x4
+
+ - peripheral_name: dp_bsn_monitor # pi_dp_bsn_monitor.py
+ peripheral_description: "Monitor the Block Sequence Number (BSN) status of streaming data."
+ parameters:
+ # Parameters of mms_dp_bsn_monitor.vhd
+ - { name: g_nof_streams, value: 1 }
+ slave_ports:
+ # MM port for dp_bsn_monitor_reg.vhd
+ - slave_name: REG_DP_BSN_MONITOR
+ slave_type: REG
+ slave_description: ""
+ number_of_slaves: g_nof_streams
+ fields:
+ - - field_name: xon_stable
+ field_description: "Data block flow control xon signal was active and stable during last sync interval."
+ width: 1
+ bit_offset: 0
+ access_mode: RO
+ address_offset: 0x0
+ - - field_name: ready_stable
+ field_description: "Clock cycle flow control ready signal was active and stable during last sync interval."
+ width: 1
+ bit_offset: 1
+ access_mode: RO
+ address_offset: 0x0
+ - - field_name: sync_timeout
+ field_description: "Data stream sync did not occur during last sync interval."
+ width: 1
+ bit_offset: 2 # EK TODO: using 1 cause gen_doc.py to fail without clear error, because fields then overlap
+ access_mode: RO
+ address_offset: 0x0
+ - - field_name: bsn_at_sync_lo
+ field_description: "Data stream BSN lo at sync."
+ access_mode: RO
+ address_offset: 0x4
+ - - field_name: bsn_at_sync_hi
+ field_description: "Data stream BSN hi at sync."
+ access_mode: RO
+ address_offset: 0x8
+ - - field_name: nof_sop
+ field_description: "Number data blocks (sop = start of packet) during last sync interval."
+ access_mode: RO
+ address_offset: 0xC
+ - - field_name: nof_valid
+ field_description: "Number valid samples of the data blocks during last sync interval (= nof_sop * block size)."
+ access_mode: RO
+ address_offset: 0x10
+ - - field_name: nof_err
+ field_description: "Number data blocks with error indication during last sync interval."
+ access_mode: RO
+ address_offset: 0x14
+ - - field_name: bsn_first_lo
+ field_description: "First data stream BSN lo ever."
+ access_mode: RO
+ address_offset: 0x18
+ - - field_name: bsn_first_hi
+ field_description: "First data stream BSN hi ever."
+ access_mode: RO
+ address_offset: 0x1C
+ - - field_name: bsn_first_cycle_cnt
+ field_description: "Arrival latency of first data stream BSN ever, relative to local sync."
+ access_mode: RO
+ address_offset: 0x20
+
+ - peripheral_name: dp_bsn_monitor_v2 # pi_dp_bsn_monitor_v2.py
+ peripheral_description: "Monitor the Block Sequence Number (BSN) status and latency of streaming data."
+ parameters:
+ # Parameters of mms_dp_bsn_monitor_v2.vhd
+ - { name: g_nof_streams, value: 1 }
+ slave_ports:
+ # MM port for dp_bsn_monitor_reg_v2.vhd
+ - slave_name: REG_DP_BSN_MONITOR_V2
+ slave_type: REG
+ slave_description: ""
+ number_of_slaves: g_nof_streams
+ fields:
+ - - field_name: xon_stable
+ field_description: "Data block flow control xon signal was active and stable during last sync interval."
+ width: 1
+ bit_offset: 0
+ access_mode: RO
+ address_offset: 0x0
+ - - field_name: ready_stable
+ field_description: "Clock cycle flow control ready signal was active and stable during last sync interval."
+ width: 1
+ bit_offset: 1
+ access_mode: RO
+ address_offset: 0x0
+ - - field_name: sync_timeout
+ field_description: "Data stream sync did not occur during last sync interval."
+ width: 1
+ bit_offset: 1
+ access_mode: RO
+ address_offset: 0x0
+ - - field_name: bsn_at_sync_lo
+ field_description: "Data stream BSN lo at sync."
+ access_mode: RO
+ address_offset: 0x4
+ - - field_name: bsn_at_sync_hi
+ field_description: "Data stream BSN hi at sync."
+ access_mode: RO
+ address_offset: 0x8
+ - - field_name: nof_sop
+ field_description: "Number data blocks (sop = start of packet) during last sync interval."
+ access_mode: RO
+ address_offset: 0xC
+ - - field_name: nof_valid
+ field_description: "Number valid samples of the data blocks during last sync interval (= nof_sop * block size)."
+ access_mode: RO
+ address_offset: 0x10
+ - - field_name: nof_err
+ field_description: "Number data blocks with error indication during last sync interval."
+ access_mode: RO
+ address_offset: 0x14
+ - - field_name: latency
+ field_description: "Arrival latency of data stream BSN at sync, relative to local sync."
+ access_mode: RO
+ address_offset: 0x20